For all who don't already know.
I was on my way to the car wash and I hit 5k and the car started sputtering. I went and washed my car at Chapel Hills Mall, I even got the motor all nice and clean. After the car wash the car started fine but would not run right. I thought it might be the carb. I took it for a quick drive around the mall parking lot. I then stopped in a parking space and the car stalled. I went to try and start it back up and it would not turn over. I tried to turn it over by hand and it wont budge. My guess is it blew at least 1 apex seal in the rear and jammed the rotor. I guess 178k is what that motor lasted to.
Thanks to all who gave me a ride on Saturday. I had a great time at the meet, helped me to not think of the car.
I left the car at the mall that night and I worried about if all night. I made my wife take me on a Sunday morning drive by. The car is now safe at home.
The car will be brought back to life. I will start taring into it soon. I may work on the body while I wait for the new motor to come in. I will keep everyone posted as this progresses.
First Car To Die On The Way To A Meet
- RX-7 Chris
- Posts: 7800
- Joined: Tue Oct 02, 2007 9:14
- Location: Colorado Springs
- Contact:
1984 RX-7 GSL-SE [size=84]My restomod project[/SIZE]
1964 Ford Galaxie 500XL flat black w/ white interior, 2 dr fastback, 390 thunderbird, C6 auto, 2500 rpm high stall converter, shift kit, AC, Holley 750 cfm
[size=100]RIP 1983 RX-7[/SIZE]
My Car Blog
- RX-7 Chris
- Posts: 7800
- Joined: Tue Oct 02, 2007 9:14
- Location: Colorado Springs
- Contact:
Yes you can turn a rotory by hand. No backpressure, makes it hard to stay on a hill with no parking brake.
1984 RX-7 GSL-SE [size=84]My restomod project[/SIZE]
1964 Ford Galaxie 500XL flat black w/ white interior, 2 dr fastback, 390 thunderbird, C6 auto, 2500 rpm high stall converter, shift kit, AC, Holley 750 cfm
[size=100]RIP 1983 RX-7[/SIZE]
My Car Blog
<div class='quotetop'>QUOTE (RX-7 Chris @ Jan 14 2008, 09:37 AM) [url=index.php?act=findpost&pid=18063]<{POST_SNAPBACK}>[/url]</div>
178k miles...wow..you rebuilding or swapping?
Yes you can turn a rotory by hand. No backpressure, makes it hard to stay on a hill with no parking brake.[/b]
178k miles...wow..you rebuilding or swapping?

"20<cut off="">"</cut>
- RX-7 Chris
- Posts: 7800
- Joined: Tue Oct 02, 2007 9:14
- Location: Colorado Springs
- Contact:
I will be swapping in a streetport 12a. I am going to be looking into the finances this week. The setup I want is going to cost about $3k. I will be putting a holley carb setup unless I can get something else used for cheaper.
If anyone has a carb setup for a streetport 12a, PM me.
If anyone has a carb setup for a streetport 12a, PM me.
1984 RX-7 GSL-SE [size=84]My restomod project[/SIZE]
1964 Ford Galaxie 500XL flat black w/ white interior, 2 dr fastback, 390 thunderbird, C6 auto, 2500 rpm high stall converter, shift kit, AC, Holley 750 cfm
[size=100]RIP 1983 RX-7[/SIZE]
My Car Blog
<div class='quotetop'>QUOTE (RX-7 Chris @ Jan 14 2008, 10:19 AM) [url=index.php?act=findpost&pid=18082]<{POST_SNAPBACK}>[/url]</div>
wow g/l with this setup....can't wait to see the finished product.
I will be swapping in a streetport 12a. I am going to be looking into the finances this week. The setup I want is going to cost about $3k. I will be putting a holley carb setup unless I can get something else used for cheaper.
If anyone has a carb setup for a streetport 12a, PM me.[/b]
wow g/l with this setup....can't wait to see the finished product.
"20<cut off="">"</cut>
- RX-7 Chris
- Posts: 7800
- Joined: Tue Oct 02, 2007 9:14
- Location: Colorado Springs
- Contact:
The main thing I am looking for is the carb setup.
I would prefer a holley setup but I would be happy with whatever right now.
I would prefer a holley setup but I would be happy with whatever right now.
1984 RX-7 GSL-SE [size=84]My restomod project[/SIZE]
1964 Ford Galaxie 500XL flat black w/ white interior, 2 dr fastback, 390 thunderbird, C6 auto, 2500 rpm high stall converter, shift kit, AC, Holley 750 cfm
[size=100]RIP 1983 RX-7[/SIZE]
My Car Blog
- Colombia28
- Posts: 4216
- Joined: Wed Sep 19, 2007 9:14
- Location: Lone Tree
- Contact:
- goldrocket
- Posts: 857
- Joined: Wed Oct 31, 2007 9:14
- Location: Colorado Springs
- Contact:
Hey Chris, I don't know if you have been there or not, but go to Mazdspeed.com and post what you are looking for. That is the all first gen website i told you about on Saturday. I would be willing to bet you'll find the Holley or a weber setup from one of they guys there. They are all pretty cool and they have a ton of parts, cars and knowledge. If you are still unsure about who to build you engine I can tell you from experience and TWO blown apex seals that Rotary Warehouse is awesome. I didn't need to replace a housing on mine, and I'm sure most builders would be quick to prey upon the possibility of needing an expensive part like a rotor housing. Here is the link Rotary Warehouse The engine I got is a stage 4 13b four port. A stage 4 12a will cost you under 3K.
Al says
Anything worth doing is worth overdoing!:eek:

Anything worth doing is worth overdoing!:eek:

- goldrocket
- Posts: 857
- Joined: Wed Oct 31, 2007 9:14
- Location: Colorado Springs
- Contact:
<div class='quotetop'>QUOTE (MazdaTom @ Jan 14 2008, 09:24 AM) [url=index.php?act=findpost&pid=18060]<{POST_SNAPBACK}>[/url]</div>
Magical dorito?!?!?! ROFL!!!! That's jacked up! And yes, the lack of valves and heads makes it easy to turn a rotary engine over by hand.
No more magical spinning dorrito for you! But 178,000 miles out of it is a pretty good run. Sucks anyway though.
You can turn over the motor "by hand" on an RX-7?[/b]
Magical dorito?!?!?! ROFL!!!! That's jacked up! And yes, the lack of valves and heads makes it easy to turn a rotary engine over by hand.
Al says
Anything worth doing is worth overdoing!:eek:

Anything worth doing is worth overdoing!:eek:

<div class='quotetop'>QUOTE (goldrocket @ Jan 14 2008, 07:36 PM) [url=index.php?act=findpost&pid=18199]<{POST_SNAPBACK}>[/url]</div>
Everyday someone has a comment to make about me having a rotary and everyday I have something new to explain why it's better
Magical dorito?!?!?! ROFL!!!! That's jacked up! And yes, the lack of valves and heads makes it easy to turn a rotary engine over by hand.[/b]
Everyday someone has a comment to make about me having a rotary and everyday I have something new to explain why it's better

[SIGPIC][/SIGPIC]
Mods:
Veilside D1-GT Body kit, Axailflow Short Shifter, Innovate LC-1 Wideband, Proshift Gauges, Greddy Turbo Kit w/ Cobb AccessPORT, TurboXS exhaust w/ race pipe, CarPC, Synapse BOV, AEM Intake
Mods:
Veilside D1-GT Body kit, Axailflow Short Shifter, Innovate LC-1 Wideband, Proshift Gauges, Greddy Turbo Kit w/ Cobb AccessPORT, TurboXS exhaust w/ race pipe, CarPC, Synapse BOV, AEM Intake
- Colombia28
- Posts: 4216
- Joined: Wed Sep 19, 2007 9:14
- Location: Lone Tree
- Contact:
- RX-7 Chris
- Posts: 7800
- Joined: Tue Oct 02, 2007 9:14
- Location: Colorado Springs
- Contact:
I don't really need a nikki setup but there are other things a need.
1984 RX-7 GSL-SE [size=84]My restomod project[/SIZE]
1964 Ford Galaxie 500XL flat black w/ white interior, 2 dr fastback, 390 thunderbird, C6 auto, 2500 rpm high stall converter, shift kit, AC, Holley 750 cfm
[size=100]RIP 1983 RX-7[/SIZE]
My Car Blog
- RX-7 Chris
- Posts: 7800
- Joined: Tue Oct 02, 2007 9:14
- Location: Colorado Springs
- Contact:
If it is a GSL than it sould have these parts.
power window regulators with motors
power window switches
rear wiper setup (motor and arm)
There may be other stuff I can't think of.
if the body is good
front fenders
driver side door
I would by the car but I have no where to put it.
I could drive up there and take it all off myself if needed.
power window regulators with motors
power window switches
rear wiper setup (motor and arm)
There may be other stuff I can't think of.
if the body is good
front fenders
driver side door
I would by the car but I have no where to put it.
I could drive up there and take it all off myself if needed.
1984 RX-7 GSL-SE [size=84]My restomod project[/SIZE]
1964 Ford Galaxie 500XL flat black w/ white interior, 2 dr fastback, 390 thunderbird, C6 auto, 2500 rpm high stall converter, shift kit, AC, Holley 750 cfm
[size=100]RIP 1983 RX-7[/SIZE]
My Car Blog
Who is online
Users browsing this forum: No registered users and 86 guests
Sorry to hear that happened. Cant wait to see it again all fixed up and running smooth!