lsx build

turboholic · Postby **turboholic** » Fri Jul 02, 2010 9:14

Im going lsx. I will post pics here as I make progress.

I have the hinson kit, t56 tranny, 6 liter engine, nitrous kit

. LS7 clutch and flywheel is ordered.

Postby **RX-7 Chris** » Fri Jul 02, 2010 9:14

So you are going for it.

iani1.1 · Postby **iani1.1** » Fri Jul 02, 2010 9:14

sweet another fd we can talk crap about lol

good luck on the swap. wait whaat nitrous!!? damn if you can go for it

LaginWagon · Postby **LaginWagon** » Fri Jul 02, 2010 9:14

Out of a CTV-V I assume?

chickenwafer · Postby **chickenwafer** » Fri Jul 02, 2010 9:14

Any plans on motor work?

I know on those LS6 motors just an intake manifold, good set of headers (which you'll need anyways), bored TB, lightweight crank pulley, and good tuning you can pick up some serious power.

Add a cam and fudgitaboutit. Easily another 150-rwhp or more.

How much do you plan on spraying?

turboholic · Postby **turboholic** » Fri Jul 02, 2010 9:14

It's a lq9 out of a 02 Escalade. Iron block. 10:1 compression. 345hp.

The ls6 I ordered arrived with a nice crack in the block, so this is the replacement I went with.

Im going to keep the engine basically stock with headers.

150 shot.

Nice daily driver. I dont want to break axles or run 9 sec quarter mile. Car looks beautiful and I want to drive it everyday.

chickenwafer · Postby **chickenwafer** » Fri Jul 02, 2010 9:14

Sounds like fun.

Even though I still strongly believe putting anything but rotary power in an RX is sacrilege, I can't deny the attractiveness of reliable and affordable brute power.

If I did it I would probably go all out tho- twin turbo, built motor, shoot for 1000rwhp LOL. Go big or go home! But then it wouldn't be anymore reliable than a 550rwhp rotary haha.

Or drop in an LS9....hmmmm

speedjunkie · Postby **speedjunkie** » Fri Jul 02, 2010 9:14

Iron block?? That's gonna be a bit heavier than the aluminum block huh?

TwentySixB · Postby **TwentySixB** » Sat Jul 03, 2010 9:14

Why not three rotor??????? hehe everyone has a v8

speedjunkie · Postby **speedjunkie** » Sat Jul 03, 2010 9:14

^There you go Nick! LOL

turboholic · Postby **turboholic** » Sat Jul 03, 2010 9:14

Just an extra set of apex seals that can break.

chickenwafer · Postby **chickenwafer** » Sat Jul 03, 2010 9:14

Anything can break- apex seals, side seals, housings, piston rings, ring lands, complex valvetrains, etc

It's all in the matter of the tune. No matter what internal combustion engine we talk about- the more work you ask it to do (power), the more heat is produced, and the narrower the window becomes for error. This is why the Bugatti Veyron has 8 radiators, and your car has one.

20B engine failures are lower, partly due to the less of them in circulation, but also most people operate them at around 500-600rwhp, which isn't asking for that much.

Now, if you operate a 2-rotor at those power levels, it's not a matter of if, it's a matter of WHEN it's going to give up. I think you'd be happy to get 10,000 miles of abuse out of a 500rwhp 13B.

7th Heaven · Postby **7th Heaven** » Mon Jul 26, 2010 9:14

turboholic wrote:Just an extra set of apex seals that can break.

Very true!

turboholic · Postby **turboholic** » Tue Aug 13, 2013 9:14

I forgot to update this. All my mazdas have migrated down to florida, but wanted to show the swap was completed. Finished lsx project videos:

http://www.flickr.com/photos/78372641@N04/9488533530/

http://www.flickr.com/photos/78372641@N04/9485525279/

And the new project is lsx rx8. Just picked her up and all the parts for the swap plus ls1/t56 combo with 50k miles on it.

my new build by turboholic, on Flickr

erod550 · Postby **erod550** » Wed Aug 14, 2013 9:14

[ame="http://www.youtube.com/watch?v=VLnWf1sQkjY"]The Lonely Island - Jizz In My Pants - YouTube[/ame]

lsx build

lsx build

Who is online