Cheyenne MS3

CheyMS3 · Postby **CheyMS3** » Tue May 25, 2010 9:14

deepSpeedMS3 wrote:well either way if you want it...let me know... if it doesnt work ill just take it back

yah ill letcha know. PM an asking price!

my wife and i will actually be down in denver tomorrow to drop my mom off at the airport...if you'll be around and the price is right, i can swing by.

MSP SuperStreet · Postby **MSP SuperStreet** » Tue May 25, 2010 9:14

Welcome
Another Mazdaspeed
ZOOM ZOOM

Operator · Postby **Operator** » Wed May 26, 2010 9:14

bellalyssa wrote:
Stick with SCR, they are amazing at what they do.

Truth, but your wallet may not be happy with you. But good work doesn't come cheap............. Just had them fix an suspension install.

erod550 · Postby **erod550** » Wed May 26, 2010 9:14

If the Cobb SRI for the first gens fits the second gens I don't see why the CP-E one wouldn't fit. I'd check around on MSF.org first though cause I'm sure someone has tried it.

Oh and welcome to the club!

TheNewBlack · Postby **TheNewBlack** » Wed May 26, 2010 9:14

erod550 wrote:If the Cobb SRI for the first gens fits the second gens I don't see why the CP-E one wouldn't fit. I'd check around on MSF.org first though cause I'm sure someone has tried it.

Oh and welcome to the club!

I have the Cobb SRI..Was told by Cobb it would be fine to use it...but if CPE has one specifically for the 2010 get that. I have a feeling its the same part # listed under 1st Gen and 2nd gen.

CheyMS3 · Postby **CheyMS3** » Wed May 26, 2010 9:14

TheNewBlack wrote:I have the Cobb SRI..Was told by Cobb it would be fine to use it...but if CPE has one specifically for the 2010 get that. I have a feeling its the same part # listed under 1st Gen and 2nd gen.

A guy off MSF got an email from Paula from CPe stating that the 1stgen Nano would work for the 2ndgen MS3 because "its the same intake".

so I should be good with gettin' the 1stgen Nano..i hope.

erod550 · Postby **erod550** » Wed May 26, 2010 9:14

Just saying if the mounting points are the same for the Cobb, they have to be the same for the CP-E too. And the engine is basically unchanged so the design should be fine as far as the MAF housing goes.

CheyMS3 · Postby **CheyMS3** » Wed May 26, 2010 9:14

went onto the CPe website, and the 1st and 2nd gen intakes do have DIFFERENT part numbers...so i emailed CPe myself and asked them to let me know if I can use a 1stgen intake on a 2010...and if not, to explain the reason.

hope to hear back tomorrow.

and I was supposed to get my kit to allow my BOV to vent to atmosphere today..but SCR didn't recieve my part today! Hope to get it tomorrow...if only Loveland wasn't such a long drive from Cheyenne lol

TheNewBlack · Postby **TheNewBlack** » Wed May 26, 2010 9:14

In that case id say its safe to use either....but obviously there were changes made so if you want to spend the extra money to get the gen2 model, then do that. My Cobb fit perfectly and Cobb said no changes were necessary for it to work. They also told me they tested one first to be sure.

TheNewBlack · Postby **TheNewBlack** » Wed May 26, 2010 9:14

CheyMS3 wrote:went onto the CPe website, and the 1st and 2nd gen intakes do have DIFFERENT part numbers...so i emailed CPe myself and asked them to let me know if I can use a 1stgen intake on a 2010...and if not, to explain the reason.

hope to hear back tomorrow.

and I was supposed to get my kit to allow my BOV to vent to atmosphere today..but SCR didn't recieve my part today! Hope to get it tomorrow...if only Loveland wasn't such a long drive from Cheyenne lol

Im interested to hear what the changes were from the 1stgen.

CheyMS3 · Postby **CheyMS3** » Wed May 26, 2010 9:14

yah, i duno what they could have done to it....i meen, its the same 2.3 DISI turbo engine.

oh well, my BOV will satisfy me wanting to hear a cool noise until I can figure out the CPe intake mystery lol

deepSpeedMS3 · Postby **deepSpeedMS3** » Thu May 27, 2010 9:14

like i said....just let me know what CP-e says

bellalyssa · Postby **bellalyssa** » Thu May 27, 2010 9:14

CheyMS3 wrote:and I was supposed to get my kit to allow my BOV to vent to atmosphere today..but SCR didn't recieve my part today! Hope to get it tomorrow...if only Loveland wasn't such a long drive from Cheyenne lol

If you ever need an intermediary, I am usually at SCR 2 or 3 times a week. I can pick it up and you can meet me in FC, if that makes it any easier for you.

Operator wrote:Truth, but your wallet may not be happy with you. But good work doesn't come cheap............. Just had them fix an suspension install.

They are mildly expensive but it's worth it. They guarantee everything they do and if they mess it up they will fix it. Thus far, they haven't done anything to me that has caused me to lose faith in them. Plus, if you don't want to take it to them they provide awesome support if you want to try it yourself.

What color is your Audi? What year?

CheyMS3 · Postby **CheyMS3** » Thu May 27, 2010 9:14

I thought I met you yesturday Bellalyssa.. guess it was another woman with a Mazda3.. (thats not supposed to sound sly and snobby lol)

Anyone know a woman who is around SCR alot with a blue Mz3?...i assume she wasn't on this forum since she didn't mention it when we talked.

Operator · Postby **Operator** » Thu May 27, 2010 9:14

bellalyssa wrote:They are mildly expensive but it's worth it. They guarantee everything they do and if they mess it up they will fix it. Thus far, they haven't done anything to me that has caused me to lose faith in them. Plus, if you don't want to take it to them they provide awesome support if you want to try it yourself.

What color is your Audi? What year?

Oh, I wasn't knocking them, like I said, I know they do good quality work. Brilliant Red/2007.

Cheyenne MS3

Who is online