Search found 237 matches
- Fri Sep 09, 2022 9:14
- Forum: Rotary Vehicle
- Topic: Build thread
- Replies: 2531
- Views: 444697
Re: Build thread
I got a headache re-reading the 1994 FSM to ensure I fully understood the inputs/outputs & logic of your specific year a/c system. Here's the corrections to my earlier post: This is the input/output & logic that you want inputted into your standalone ECU: - Input: 1E; Output: 1L (Chris was r...
- Tue Sep 06, 2022 9:14
- Forum: Rotary Vehicle
- Topic: Build thread
- Replies: 2531
- Views: 444697
Re: Build thread
My mistake on the blower resistor. I misread your post and thought you couldn't get your a/c to work due to no ground. Instead, it's the complete opposite... my bad. Here's my 2 cents: I'm not too familiar with Syvecs, but I assume you're using some sort of standalone ECU to control the engine &...
- Mon Sep 05, 2022 9:14
- Forum: Rotary Vehicle
- Topic: Build thread
- Replies: 2531
- Views: 444697
Re: Build thread
Eric... after 6 years overseas, I'm finally back on the mainland. Unfortunately I have zero updates on my FD since it's been in storage the entire time. But I just viewed your build, and OMG... you've been through a lot. I admire your courage and persistence on building your dream car, especially wi...
- Tue Sep 06, 2016 9:14
- Forum: Rotary Vehicle
- Topic: Build thread
- Replies: 2531
- Views: 444697
Re: Build thread
I'm off starting tomorrow. So if you want help troubleshooting your starting issues, let me know... I've got all my starting issues solved. Since my parts arrive Friday, I have some free time before I start tearing my car down.
- Thu Sep 01, 2016 9:14
- Forum: Rotary Vehicle
- Topic: Build thread
- Replies: 2531
- Views: 444697
Re: Build thread
Hey Eric. I've been away from the Springs for quite a few months, and just got back in town. I'm going to take my car down for surgery after this weekend. So if you're looking for another rx7 to join the fun, just let me know the time/place. Btw, great job on your progress!
- Wed Apr 13, 2016 9:14
- Forum: Colorado Automotive Enthusiasts Meets and Events
- Topic: Rescheduled Tech Meet/Pot Luck May 7th
- Replies: 39
- Views: 13281
Re: Tech Meet/Pot Luck April 16th
Btw, the weather is predicted to be pretty dicey Saturday. You may want to consider an alternate date.
- Tue Apr 12, 2016 9:14
- Forum: Colorado Automotive Enthusiasts Meets and Events
- Topic: Rescheduled Tech Meet/Pot Luck May 7th
- Replies: 39
- Views: 13281
Re: Tech Meet/Pot Luck April 16th
I can bring some soft drinks & chips. You may need to text me your address again.
- Tue Apr 12, 2016 9:14
- Forum: Rotary Vehicle
- Topic: Build thread
- Replies: 2531
- Views: 444697
Re: Build thread
I've done both methods. When I lived in Florida, my dryer was in the garage. So using the dryer receptacle for my high voltage needs made sense. Here (Colorado), my dryer is on the second floor, so using that method wasn't practical. Since the circuit breaker is in the garage, installing a 240v rece...
- Fri Apr 01, 2016 9:14
- Forum: Rotary Vehicle
- Topic: Build thread
- Replies: 2531
- Views: 444697
Re: Build thread
Getting those angles correct so the DP mates up to your existing exhaust system must've been a painstaking chore. The result turned out good though. If it's stainless, hopefully your welder backpurges the pipe when he does the final weld.
- Mon Mar 28, 2016 9:14
- Forum: Rotary Vehicle
- Topic: FDEEZ's Build Thread
- Replies: 140
- Views: 45428
Re: FDEEZ's Build Thread
Between AutoZone and O'Reillys, you can source them all locally. I found that the O'Reillys on Powers and Omaha Blvd has the largest selection in stock. But like you said, it's better if you saw the results in person before purchasing them. You may not like the light output over the aftermarket ones...
- Sun Mar 27, 2016 9:14
- Forum: Rotary Vehicle
- Topic: FDEEZ's Build Thread
- Replies: 140
- Views: 45428
Re: FDEEZ's Build Thread
Compared to the HID headlights, the remainder of the lighting on my car looks dull and yellowish. So I went ahead and swapped out all the bulbs (except fog lights & rear license plate lights) with LEDs. I wasn't too impressed with the LED bulbs I used in the past, so I decided to spend a little ...
- Sun Mar 20, 2016 9:14
- Forum: Rotary Vehicle
- Topic: Build thread
- Replies: 2531
- Views: 444697
Re: Build thread
I figured out an Amsoil air filter that should fit, I just have to change the angle of the filter a bit, which I'm hopefully will work to my advantage anyway. I also plan to drop my condenser a bit and use fiberglass to make ducting to all the pieces in the VMIC. I'm also getting the pre-filter, an...
- Sun Mar 20, 2016 9:14
- Forum: Colorado Automotive Enthusiasts Meets and Events
- Topic: Rescheduled Tech Meet/Pot Luck May 7th
- Replies: 39
- Views: 13281
Re: Tech Meet/Pot Luck April/May
I should be able to make it.
- Sun Mar 20, 2016 9:14
- Forum: Rotary Vehicle
- Topic: FDEEZ's Build Thread
- Replies: 140
- Views: 45428
Re: FDEEZ's Build Thread
In brightest day, in blackest night, no evil shall escape my sight :D After weeks of working on/off with the car, I finally completed my headlight project over the weekend. Since I rarely drive my FD at night, I've tolerated the OEM headlights for a while. And if you've ever rode in a stock FD at ni...
- Thu Feb 18, 2016 9:14
- Forum: Rotary Vehicle
- Topic: Build thread
- Replies: 2531
- Views: 444697
Re: Build thread
Do you have any pics of the gussets the people did? I'm curious how they did it. Good luck on finding pictures. It's mainly considered a trade secret. If you're really interested, try calling Speedfab in Florida. They gusset the stock mounting tabs/points of all the rear FD subframes they convert t...