Search found 553 matches

by D Walker
Tue Sep 23, 2014 9:14
Forum: Rotary Vehicle
Topic: Build Thread
Replies: 109
Views: 25805

You know I can get injectors tested locally?
by D Walker
Mon Sep 22, 2014 9:14
Forum: Rotary Vehicle
Topic: Build thread
Replies: 2518
Views: 433763

Eric a couple of things about your setup I have been meaning to comment on. One of the key yhings, and I see a lot of guys doing this, is that its a bad idea to run two high volume pumps all the time, especially at startup, idle, and light load. Its harder on the fuel system components, puts a lot o...
by D Walker
Fri Sep 19, 2014 9:14
Forum: Rotary Vehicle
Topic: Build thread
Replies: 2518
Views: 433763

Eric starter signal from the switch rarely has anything to do with slow cranking as long as your getting some voltage to the starter solenoid to trip it. I would check, in order: Starter- an starter that sometimes cranks fast and then sometimes slow can have damaged. Excessive or repeated cranking r...
by D Walker
Tue Sep 16, 2014 9:14
Forum: Car Chat
Topic: Possible ATDS Mazda scam??
Replies: 2
Views: 1881

Easy enough to check out, call Mazda North America in CA and ask.

What they could be testing is the emissions level at the current milage over a variety of conditions. Emissions system effectiveness, etc.
by D Walker
Tue Sep 16, 2014 9:14
Forum: Rotary Vehicle
Topic: Build Thread
Replies: 109
Views: 25805

What are you using to tune with?
by D Walker
Sat Sep 13, 2014 9:14
Forum: For Sale/Wanted
Topic: FOR SALE Ben Pearson Lift
Replies: 0
Views: 1290

FOR SALE Ben Pearson Lift

Selling my lift. Its an older Ben Pearson that has been modified to fit 12' ceilings but allow full lift height for cars and most trucks, vans to almost full height. The GOOD: Had the electric motor rebuilt by Bobs Electric Motor service years ago, still works just as it should. Newer, 3-4 years old...
by D Walker
Fri Sep 12, 2014 9:14
Forum: Rotary Vehicle
Topic: Rocket Bunny.. GO!
Replies: 24
Views: 7171

You can get an RX7 to pass emissions with a single turbo. The air pump problem is that most emissions guys actually look at the computer that says it is supposed to have one, but most dont. If they look and its not there, instant fail. I wont go "big single", but I have a GT3582R on my counter that ...
by D Walker
Thu Sep 11, 2014 9:14
Forum: Rotary Vehicle
Topic: Rocket Bunny.. GO!
Replies: 24
Views: 7171

yea not really sure...
by D Walker
Wed Sep 10, 2014 9:14
Forum: Rotary Vehicle
Topic: Rocket Bunny.. GO!
Replies: 24
Views: 7171

Motor is out and just disgusting, seems to have leaked something from everywhere at one point in time or the other. Tomorrow I will break the motor down and see what can and cannot be used and clean up the nasty bits. Should probably fill the parts cleaner up and let everything soak for a day or two...
by D Walker
Wed Sep 10, 2014 9:14
Forum: Rotary Vehicle
Topic: Rocket Bunny.. GO!
Replies: 24
Views: 7171

I think the grind marks on the swaybar bushings point in the direction of impact, perhaps multiple impacts... But yeah the stock mounts suck and as it happens I make a solution for that, just kinda amazed at how twisted the front mounts are, but then again that explains the lack of an undertray and ...
by D Walker
Tue Sep 09, 2014 9:14
Forum: Rotary Vehicle
Topic: Rocket Bunny.. GO!
Replies: 24
Views: 7171

Started to pull the motor today, should have had it out but other things interfered. The underside of the car is in good condition, since as an RX7 it was preserved in oil. Going to take a lot of foamy engine degreaser and simple green to remove the years of oil, grease, and road smut from the subfr...
by D Walker
Mon Sep 08, 2014 9:14
Forum: Rotary Vehicle
Topic: Rocket Bunny.. GO!
Replies: 24
Views: 7171

Yeah, still wide. Pretty positive wheel spacers are not an option. I spoke with Enkei today and it looks like I can have a set of the 6666 Wheels made in 17x9.5 -30 front and 17x10.5 -60 rear, but it is definitely going to cost. Motor will come out tomorrow, should have the kit fitted by Thursday, t...
by D Walker
Mon Sep 08, 2014 9:14
Forum: Rotary Vehicle
Topic: Rocket Bunny.. GO!
Replies: 24
Views: 7171

Very very Wide!
by D Walker
Fri Sep 05, 2014 9:14
Forum: Rotary Vehicle
Topic: FDEEZ's Build Thread
Replies: 140
Views: 43046

Absolutely.
by D Walker
Thu Sep 04, 2014 9:14
Forum: Rotary Vehicle
Topic: FDEEZ's Build Thread
Replies: 140
Views: 43046

I do my own race car alignments..

Go to advanced search